+++Date last modified: 05-Jul-1997 PC Parallel Port Mini-FAQ By Kris Heidenstrom (kheidens@actrix.gen.nz), revision 3, 950331 1. INTRO This is a four printed page mini-FAQ with the information essential for programming the PC parallel port. Many subjects are not covered in detail. View on an 80-column screen with 8-column tab stops. Comments and suggestions to kheidenstrom@actrix.gen.nz. A parallel port links software to the real world. To software, the parallel port is three 8-bit registers occupying three consecutive addresses in the I/O space. To hardware, the port is a female 25-pin D-sub connector, carrying twelve latched outputs from the computer, accepting five inputs into the computer, with eight ground lines. The normal function of the port is to transfer data to a printer through the eight data pins, using the remaining signals as flow control and miscellaneous controls and indications. The original port was implemented with TTL/LS logic. Modern ports are implemented in an ASIC or a combined serial/parallel port chip, but are backward compatible. Some modern ports are bidirectional. 2. BIOS LPT PORT TABLE A parallel port is identified by its I/O base address, and also by its LPT port number. The BIOS power-on self-test checks specific I/O addresses for the presence of a parallel port, and builds a table of I/O addresses in the low memory BIOS data area, starting at address 0040:0008 (or 0000:0408). This table contains up to three 16-bit words. Each entry is the I/O base address of a parallel port. The first word is the I/O base address of LPT1, the second is LPT2, etc. If less than three ports were found, the remaining entries in the table are zero. DOS, and the BIOS printer functions (accessed via int 17h), use this table to translate an LPT port number to a physical port at a certain address. The addresses are checked in a specific order, and addresses are put into the table as they are found, so the table will never have gaps. A particular I/O address does not necessarily always equate to the same specific LPT port number, although there are conventions. 2.1 ADDRESSING CONVENTIONS The video card's parallel port is normally at 3BCh. This address is checked first by the BIOS, so if a port exists there, it will be LPT1. The BIOS then checks at 378h, then at 278h. AFAIK there is no standard address for a fourth port, and BIOSes only look for three. 3. DIRECT HARDWARE ACCESS The port consists of three 8-bit registers at adjacent addresses in the processor's I/O space. The registers are defined relative to the I/O base address, and are at IOBase+0, IOBase+1, and IOBase+2 (for example if IOBase is 3BCh, then the registers are at 3BCh, 3BDh, and 3BEh). Always use 8-bit I/O accesses on these registers. 3.1 DATA REGISTER The data register is at IOBase+0. It may be read and written (using the IN and OUT instructions, or inportb() and outportb() or inp() and outp()). Writing a byte to this register causes the byte value to appear on pins 2 through 9 of the D-sub connector (unless the port is bidirectional and is set to input mode). The value will remain latched and stable until you write another value to the data register. Reading this register yields the state of those pins. 7 6 5 4 3 2 1 0 * . . . . . . . D7 (pin 9), 1=High, 0=Low . * . . . . . . D6 (pin 8), 1=High, 0=Low . . * . . . . . D5 (pin 7), 1=High, 0=Low . . . * . . . . D4 (pin 6), 1=High, 0=Low . . . . * . . . D3 (pin 5), 1=High, 0=Low . . . . . * . . D2 (pin 4), 1=High, 0=Low . . . . . . * . D1 (pin 3), 1=High, 0=Low . . . . . . . * D0 (pin 2), 1=High, 0=Low 3.2 STATUS REGISTER The status register is at IOBase+1. It is read-only (writes will be ignored). Reading the port yields the state of the five status input pins on the parallel port connector at the time of the read access: 7 6 5 4 3 2 1 0 * . . . . . . . Busy . . (pin 11), high=0, low=1 (inverted) . * . . . . . . Ack . . (pin 10), high=1, low=0 (true) . . * . . . . . No paper (pin 12), high=1, low=0 (true) . . . * . . . . Selected (pin 13), high=1, low=0 (true) . . . . * . . . Error. . (pin 15), high=1, low=0 (true) . . . . . * * * Undefined 3.3 CONTROL REGISTER The control register is at IOBase+2. It is read/write: 7 6 5 4 3 2 1 0 * * . . . . . . Unused (undefined on read, ignored on write) . . * . . . . . Bidirectional control, see below . . . * . . . . Interrupt control, 1=enable, 0=disable . . . . * . . . Select . . (pin 17), 1=low, 0=high (inverted) . . . . . * . . Initialize (pin 16), 1=high, 0=low (true) . . . . . . * . Auto Feed (pin 14), 1=low, 0=high (inverted) . . . . . . . * Strobe . . (pin 1), 1=low, 0=high (inverted) 3.3.1 BIDIRECTIONAL CONTROL BIT The bidirectional control bit is only supported on true bidirectional ports - on other ports, it behaves like bits 7 and 6. On a proper bidirectional port, setting this bit to '1' causes the outputs of the buffer that drives pins 2 through 9 of the 25-pin connector to go into a high-impedance state, so that data can be _input_ on those pins. In this state, values written to the data register will be stored in the latch chip, but not asserted on the connector, and reading the data register will yield the states of the pins, which may be driven by an external device without stressing or damaging the port driver. Also note that on some machines, another port must be set correctly to enable the bidirectional features, in addition to this bit. I suspect this applies to machines with the parallel port integrated on the motherboard as part of the motherboard chipset, but I do not have details, sorry. On some parallel port cards, bidirectional mode must be enabled by a jumper setting. With this setting enabled, the bidirectional control bit will be able to enable the bidirectional input mode. 3.3.2 INTERRUPT ENABLE BIT DOS and BIOS do not use the interrupt facility of the parallel port during printing. OS/2 versions up to 2.11 did use and rely on the parallel port interrupt but OS/2 Warp does not by default. For experimenters, the interrupt facility is useful as a general purpose externally triggerable interrupt input. The interrupt control bit controls a tristate buffer that drives the IRQ line. Setting the bit to '1' enables the buffer, and an IRQ will be triggered on each falling edge (high to low transition) of the Ack signal on pin 10 of the 25-pin connector. Disabling the interrupt allows other devices to use the IRQ line. The actual IRQ number is either hardwired (by convention, the port at 3BCh uses IRQ7), or is jumper-selectable (IRQ5 is a common choice). Sound cards, in particular, tend to use IRQ7 for their own purposes. To use the IRQ you must also enable the interrupt via the interrupt mask register in the interrupt controller, at I/O address 21h, and your interrupt handler must send an EOI on exit. DOS technical programming references have notes on writing interrupt handlers. 3.3.3 PRINTER CONTROL BITS The bottom four bits are latched and presented on the parallel port connector, much like the data register. Three of them are inverted, so writing a '1' will output a low voltage on the port pin for them. These four outputs are open collector outputs with pullup resistors, so an external device can force them low without stressing the driver in the PC, and they can even be used as inputs. To use them as inputs, write 0100 binary to the bottom four bits of the control register. This sets the outputs all high, so they are pulled high by the pullup resistors (typically 4700 ohms). An external device can then pull them low, and you can read the pin states by reading the control register. Remember to allow for the inversion on three of the pins. If you are using this technique, the control register is not strictly 'read/write', because you may not read what you write (or wrote). 4 SAMPLE PROGRAM - DETERMINE WHETHER A PORT IS BIDIRECTIONAL This program reports for LPT1, LPT2, and LPT3 whether the port exists and whether it is bidirectional, i.e. setting the bidirectional control bit causes the port to go into high-impedance (tri-state) mode. This program is written for Borland C. Change outportb() and inportb() to outp() and inp() for Microsoft C, I think. I did not have a machine with a bidirectional port with which to test this program fully, so please drop me a line if you can confirm that it does or doesn't work. Save this code to BIDIR.C and compile with: bcc -I -L bidir.c --------------------------- snip snip snip --------------------------- #include #include #include /* The following function returns the I/O base address of the nominated parallel port. The input value must be 1 to 3. If the return value is zero, the specified port does not exist. */ unsigned int get_lptport_iobase(unsigned int lptport_num) { return *((unsigned int far *)MK_FP(0x40, 6) + lptport_num); } /* Checks whether the port's data register retains data, returns 1 if so, 0 if not. The data register retains data on non-bidirectional ports, but on bidirectional ports in high impedance (tri-state) mode, the data register will not retain data. */ unsigned int test_retention(unsigned int iobase) { outportb(iobase, 0x55); /* Write a new value */ (void) inportb(iobase); /* Delay */ if (inportb(iobase) != 0x55) { return 0; /* Did not retain data */ } outportb(iobase, 0xAA); /* Write another new value */ (void) inportb(iobase); /* Delay */ if (inportb(iobase) != 0xAA) { return 0; /* Did not retain data */ } return 1; /* Retained data alright */ } void report_port_type(unsigned int portnum) { unsigned int iobase, oldctrl, oldval; iobase = get_lptport_iobase(portnum); if (iobase == 0) { printf("LPT%d does not exist\n", portnum); return; } oldctrl = inportb(iobase+2); outportb(iobase+2, oldctrl & 0xDF); /* Bidir off */ (void) inportb(iobase); /* Delay */ oldval = inportb(iobase); /* Keep old data */ if (test_retention(iobase) == 0) { printf("LPT%d appears to be faulty!\n", portnum); outportb(iobase+2, oldctrl); outportb(iobase, oldval); return; } outportb(iobase+2, oldctrl | 0x20); /* Bidir on */ printf("LPT%d %s bidirectional\n", portnum, (test_retention(iobase)) ? "is not" : "is"); outportb(iobase+2, oldctrl); /* Put it back */ outportb(iobase, oldval); /* Restore data */ return; } void main(void) { unsigned int portnum; for (portnum = 1; portnum < 4; ++portnum) report_port_type(portnum); exit(0); } --------------------------- snip snip snip --------------------------- 5. FILE TRANSFER PROGRAM CABLES The parallel-to-parallel cable is used by DRDOS's INTERLNK program. Apparently Laplink and FastLynx cables are the same. The pin-to-pin connection between two male 25-pin D-sub connectors is: 2-15, 3-13, 4-12, 5-10, 6-11, and the reverse: 15-2, 13-3, 12-4, 10-5, and 11-6, and ground: 25-25. This requires eleven wires. If you have spare wires, link some extra grounds together. Pins 18 to 25 inclusive are grounds. A very long cable may be unreliable, limit it to 10 metres. 6. DISCLAIMER In no event shall the author be liable for any damages whatsoever for any loss relating to this document. Use it at your own risk! End of the PC Parallel Port Mini-FAQ.